In this study, a high-confining pressure and real-time large-displacement shearing-flow setup was developed. The test setup can be used to analyze the injection pressure conditions that increase the hydro-shearing permeability and injection-induced seismicity during hot dry rock geothermal extraction. For optimizing injection strategies and improving engineering safety, real-time permeability, deformation, and energy release characteristics of fractured granite samples driven by injected water pressure under different critical sliding conditions were evaluated. The results indicated that: (1) A low injection water pressure induced intermittent small-deformation stick-slip behavior in fractures, and a high injection pressure primarily caused continuous high-speed large-deformation sliding in fractures. The optimal injection water pressure range was defined for enhancing hydraulic shear permeability and preventing large injection-induced earthquakes. (2) Under the same experimental conditions, fracture sliding was deemed as the major factor that enhanced the hydraulic shear-permeability enhancement and the maximum permeability increased by 36.54 and 41.59 times, respectively, in above two slip modes. (3) Based on the real-time transient evolution of water pressure during fracture sliding, the variation coefficients of slip rate, permeability, and water pressure were fitted, and the results were different from those measured under quasi-static conditions. (4) The maximum and minimum shear strength criteria for injection-induced fracture sliding were also determined (m = 0.6665 and m = 0.1645, respectively, m is friction coefficient). Using the 3D (three-dimensional) fracture surface scanning technology, the weakening effect of injection pressure on fracture surface damage characteristics was determined, which provided evidence for the geological markers of fault sliding mode and sliding nature transitions under the fluid influence. (c) 2025 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/ 4.0/).

Injection-induced seismicity has been a focus of industry for decades as it poses great challenges to the associated risk mitigation and hazard assessment. The response surface methodology is integrated into the geo-mechanical model to analyze the effects of multiple factors on induced seismicity during the post shut-in period. We investigate the roles of poroelastic stress and pore pressure diffusion and examine the differences in the controlling mechanism between fault damage zones and the fault core. A sensitivity analysis is conducted to rank the selected factors, followed by a Box-Behnken design to form response surfaces and formulate prediction models for the Coulomb stress and its components. Reservoir properties significantly affect the potentials of induced seismicity in the fault by changing pore pressure diffusion, which can be influenced by other factors to varying degrees. Coulomb stress is greater in pressurized damage zones than in fault cores, and the seismicity rate exhibits a consistent variation. Poroelastic stress plays a similar role to pore pressure diffusion in the stability of the fault within the pressurized damage zones. However, pore pressure diffusion dominates in the fault core due to the low rigidity, which limits the accumulation of elastic energy caused by poroelastic coupling. The slip along the fault core is a critical issue to consider. The potential for induced seismicity is reduced in the right damage zones as the pore pressure diffusion is blocked by the low-permeability fault core. However, poroelastic stressing still occurs, and in deep basements, the poroelastic effect is dominant even without a direct increase in pore pressure. The findings in this study reveal the fundamental mechanisms behind injection-induced seismicity and provide guidance for optimizing injection schemes in specific situations. (c) 2024 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/ 4.0/).

With respect to geology, most coastal terrains are underlain by problematic soils, some of which are liquefiable in nature and may cause sudden failure of engineering infrastructures. Against this background, this study was carried out to investigate the subsurface geology of some Lagos coastal areas and their engineering implications using geophysical and geotechnical methods. To achieve this purpose, the Multichannel Analysis of Surface Waves, Cone Penetration Test, and Standard Penetration Test were deployed. Surface waves measurements were collected using a 24-channel seismograph to which 4.5 Hz twenty-four vertical geophones were connected via the takeouts of the two cable reels. CPT soundings were carried out with a 10-tons motorized cone penetrometer and boring with SPT were carried out as well. The results of the Multichannel Analysis of Surface Waves measurements showed that the shear waves velocity (Vs) ranges from 160 to 470 m/s. The very loose to loose sand delineated have Vs in the range from 170 to 250 m/s. The tip resistance and sleeve resistance values spanned between 4.0 and 72.0 kg/cm2 and 6.0-94 kg/cm2 respectively. The thickness of the liquefiable sands in the study area varied between 2.5 and 18.0 m. At Ikoyi site, owing to the prevalence of loose silty sand, corroborated by the available borehole data and the Liquefaction Potential Index, it is classified as having a high-risk liquefaction and could be responsible for the periodic damages to structural infrastructures such as roads and buildings. The sediments mapped at Okun-Ajah and Badore sites are mainly saturated loose sands with high likelihood to liquefaction with very-high to high risk severity. The study concludes that the presence of these sediments and other factors that could induce ground motion making the study sites potentially susceptible to liquefaction. Hence, an urgent attention must be given to early monitoring measures to address the trend. Study assesses use of electrical resistivity imaging and seismic refraction (via Multi Analysis Surface Waves) methods for near surface mapping/characterization The study sites belong to the wetland, coastal area of the Dahomey Basin, a part of sedimentary basin with sands deposits, peat, clay and their intercalation The shear waves velocity model integrated with CPT data proved to be useful tool for evaluation of soil liquefaction status with the index suggesting low-high-very high risks