Carbonaceous aerosols play a crucial role in air pollution and radiative forcing, though their light-absorbing and isotopic characteristics remain insufficiently understood. This study analyzes optical absorption and isotopic composition in PM10 and PM2.5 particles from primary emission sources, focusing on traffic-related and solid fuel categories. We analyzed key optical properties, including the Angstrom absorption exponent (AAE), the contributions of black carbon (BC) and brown carbon (BrC) to total light absorption and the mass absorption efficiencies (MAE) of carbonaceous aerosols. AAE values were lower for traffic emission sources (0.9 to 1.3) than solid fuel emission sources (1.5 to 3), with similar values for both particle sizes. BrC contributions were more prominent at shorter wavelengths and were notably higher in solid fuel emission sources (61% to 88%) than in traffic emission sources (8% to 40%) at 405 nm. MAE values of BC at 405 nm were 2 to 20 times higher than BrC across different emissions. Particle size significantly affect MAE(BC) with PM2.5 higher when compared to PM10. Emissions from diesel concentrate mixer and raw coal burning exhibited the highest MAE(BC) for PM2.5 and PM10, respectively. Conversely, Coke had the lowest MAE(BC) but the highest MAE(BrC) for both sizes. Traffic emissions showed more stable carbon isotope ratios (delta C-13) enrichment (-29 parts per thousand to -24 parts per thousand) than solid fuels (-31 parts per thousand to -20 parts per thousand). delta C-13 of solid fuel combustion, unlike traffic sources, is found to be independent of size variation. These findings underscore the importance of source and size-specific aerosol characterization for unregulated emission sources.
The present paper sets out a comparative analysis of carbon emission and economic benefit of different performance gradients solid waste based solidification material (SSM). The macro properties of SSM were the focus of systematic study, with the aim of gaining deeper insight into the response of the SSM to conditions such as freeze-thaw cycles, seawater erosion, dry-wet cycles and dry shrinkage. In order to facilitate this study, a range of analytical techniques were employed, including scanning electron microscopy (SEM), X-ray diffraction (XRD) and mercury intrusion porosimetry (MIP). The findings indicate that, in comparison with cement, the carbon emissions of SSM (A1) are diminished by 77.7 %, amounting to 190 kg/t, the carbon-performance ratio (24.4 kg/ MPa), the cost-performance ratio (32.1RMB/MPa) and the carbon-cost ratio (0.76kg/RMB) are reduced by 86 %, 56 % and 68 % respectively. SSM demonstrated better performance in terms of freeze-thaw resistance, seawater erosion resistance and dry-wet resistance when compared to cement. The dry shrinkage value of SSM solidified soil was reduced by approximately 35 % at 40 days compared to cement solidified soil, due to compensatory shrinkage and a reduction in pores. In contrast to the relatively minor impact of seawater erosion and the moderate effects of the wet-dry cycle, freeze-thaw cycles have been shown to cause the most severe structural damage to the micro-structure of solidified soil. The conduction of durability tests resulted in increased porosity and the most probable aperture. The increase in pores and micro-structure leads to the attenuation of macroscopic mechanical properties of SSM solidified soil. The engineering application verified that with the content of SSM of 50 kg/m, 4.5 % and 3 %, the strength, bearing capacity and bending value of SSM modified soil were 1.9 MPa, 180 kPa and 158, respectively in deep mixing piles, shallow in-situ solidification, and roadbed modified soil field.
Atmospheric brown carbon (BrC) from wildfires is a key component of light-absorbing carbon that significantly contributes to global radiative forcing, but its atmospheric evolution and lifetime remain poorly understood. In this study, we investigate BrC evolution by synthesizing data from one laboratory campaign and four aircraft campaigns spanning diverse spatial scales across North America. To estimate initial conditions for evaluating plume evolution, we develop a method to parametrize the emission ratios of BrC and other species using commonly measured inert tracers, acetonitrile and hydrogen cyanide. The evolution of BrC absorption in the free troposphere is characterized as a function of hydroxyl radical (OH) exposure, yielding an effective photochemical rate constant of 9.7-1.6 +4.8 x 10-12 cm3 molecule-1 s-1. The relatively slow reaction rate results in small BrC decay within the first few hours after emission, making it difficult to distinguish from source variability. This helps explain the absence of clear evolutionary trends in near-field studies. Assuming an OH concentration of 1.26 x 106 molecules cm-3, this rate constant corresponds to an e-folding lifetime of approximately 23 h. After extensive photooxidation (OH exposure similar to 1012 molecules cm-3 s), 4 +/- 2% of the emitted BrC persists, representing a recalcitrant fraction with potential long-term climate impacts. These results improve our understanding of BrC variability and photochemical processing and provide critical constraints for modeling its impacts on climate.
Permafrost thaw represents one of Earth's largest climate feedback risks, potentially releasing vast carbon (C) stores as greenhouse gases (GHG). However, our ability to predict emissions remains limited by poor understanding of how changing organic matter (OM) composition affects microbial carbon processing. We test a metabolism-centered redox framework, which views microbial processes as coupled oxidative-reductive reactions, to mechanistically explain how organic matter metabolite quality controls greenhouse gas production in permafrost-affected peatland ecosystems. Rather than relying solely on geochemical redox measurements, our approach examines how microbes balance electron flow through metabolic pathways. Using active layer peat (9-19 cm) from contrasting environments (bog and fen), we employed multi-omics approaches, including metabolomics, metagenomics, and metatranscriptomics, to link OM chemistry to microbial function. Our results reveal distinct dissolved organic matter metabolite composition, with fen systems enriched in compounds with higher substrate quality (low molecular weight (MW) sugars with high H:C ratios and low aromaticity) and bog systems dominated by compounds with lower substrate quality (high MW phenols with lower H:C ratios and higher aromaticity). In fen samples, these sugar-like compounds correlated with higher oxidative metabolism and methanogenesis, supported by increased glycolysis gene expression. Initially, electrons from increased oxidative metabolism were balanced through nitrate and sulfate reduction, but as these electron acceptors were depleted, methanogenesis increased to maintain redox balance. Fen samples showed rapid degradation of both high- and low-substrate-quality compounds, suggesting sufficient energy for efficient C cycling. Conversely, bog samples exhibited more polyphenolic compounds, lower glycolysis activity, and higher stress-related gene expression, suggesting energy was diverted towards cell maintenance under acidic conditions rather than C processing. This approach suggests that predicting greenhouse gas emissions requires an understanding of how organic matter quality shapes microbial energy allocation strategies, providing a mechanistic framework for improving emission predictions from permafrost-affected peatlands and similar ecosystems.
This paper investigated the influence of chloride ion erosion and aftershocks on the seismic performance of transmission tower structures in Xinjiang, China. Based on chloride ion diffusion laws and steel corrosion mechanisms, the time-dependent deterioration of reinforced concrete was analyzed. Finite element models considering corrosion effects were established for different ages(0a,50a,70a,100a) in a saline soil environment using ANSYS/LS-DYNA. Ten mainshock-aftershock sequences tailored to the site type was constructed, and the cumulative damage index (DI) was adopted as a metric for structural damage. The results indicate that aftershocks and steel corrosion significantly impact transmission tower damage, with damage extent influenced by the intensity of the main shock. Stronger aftershocks cause greater additional damage, potentially exceeding 50 % cumulative damage when their amplitude matches the main shock. Steel corrosion alone can lead to nearly 40 % damage. Its influence on seismic fragility varies with damage state, especially under moderate to complete damage, where longer service life increases vulnerability. The coupling of corrosion and aftershocks further elevates structural vulnerability. Hence, in seismic assessments of transmission towers in saline soil environments, combined effects of main and aftershocks, and corrosion, must be accounted for.
Soil salinization is a growing concern that degrades soil quality and inhibits agricultural productivity. Miscanthus species have received wide attention because of their high calorific potential, their value as an energy plant, and their ability to maintain high biomass accumulation. However, most studies focused on the biochemical and physiological responses to salt stress while neglecting the osmotic adjustment processes and the contribution of both organic and inorganic substances to these processes. This study evaluates the response mechanism of Miscanthus sinensis to salt stress (0-300 mM of NaCl) by evaluating the growth and photosynthetic parameters, photosynthetic response to light, and contribution of organic and inorganic substances to osmotic potential. The results revealed that M. sinensis adopted Na + compartmentalization and reallocation of biomass to the aboveground parts to mitigate the negative impact of salinity stress. Specifically, Na+ accumulated more in the root and leaf, with an increment magnitude of 75.4-173.9 and 56.7-217.1 times, respectively. This was supported by the changing trend of the stem/leaf ratio (25.1 %-55.9 %) compared to the root/shoot ratio (12.3 %-18.3 %). Also, salt-induced stress decreased the leaf's water content and water use efficiency as a result of low intracellular osmosis, and to mitigate osmotic damage, M. sinensis enhanced the accumulation of proline. These results offer theoretical and scientific insights into managing the cultivation and improving the yield of M. sinensis and other energy herbaceous plants in saline soils.
CONTEXT: Policy issues in most nations include adapting primary agricultural production to reduce greenhouse gas (GHG) emissions. Commitments have been established through multi-lateral agreements targeting GHG emission reductions to abate climate change impacts. In response to policy initiatives targeted at industries such as agriculture, producers are adopting innovative production methods and technologies to provide environmental services and mitigate emissions. GHG emissions arising from livestock production contribute to a damaging narrative surrounding agriculture, particularly beef production. OBJECTIVE: The purpose of this study is three-fold, quantifying (a) net emissions,2 (b) changes in practice, and (c) economic outcomes attributed to the forage production facet of cow-calf production. METHODS: The Saskatchewan Forage Production Survey was developed to gather forage management practices data, placing emphasis on land use and land management changes. Canada's whole-farm assessment model, Holos, was applied as a carbon accounting framework to derive the net emissions of the forage production cycle. RESULTS AND CONCLUSIONS: Results indicate carbon sequestration increased between the periods of 1991-94 and 2016-19. Gross emissions decreased to a larger degree and net emission results for the forage production facet of the Saskatchewan cow calf sector are -0.123 Mg CO2e/ha/yr in 2016-19. SIGNIFICANCE: Recommendations include the renewal of forage rejuvenation funding programs that may improve forage yields and carbon sequestration potential. Further, the expansion of term conservation easement programs to include non-native forage lands is recommended to incentivize the retention of forage land.
Widespread changes to near-surface permafrost in northern ecosystems are occurring through gradual top-down thaw and more abrupt localized thermokarst development. Both thaw types are associated with a loss of ecosystem services, including soil hydrothermal and mechanical stability and long-term carbon storage. Here, we analyzed relationships between the vascular understory, basal moss layer, active layer thickness (ALT), and greenhouse gas fluxes along a thaw gradient from permafrost peat plateau to thaw bog in Interior Alaska. We used ALT to define four distinct stages of thaw: Stable, Early, Intermediate, and Advanced, and we identified key plant taxa that serve as reliable indicators of each stage. Advanced thaw, with a thicker active layer and more developed thermokarst features, was associated with increased abundance of graminoids and Sphagnum mosses but decreased plant species richness and ericoid abundance, as well as a substantial increase in methane emissions. Early thaw, characterized by active layer thickening without thermokarst development, coincided with decreased ericoid cover and plant species richness and an increase in CH4 emissions. Our findings suggest that early stages of thaw, prior to the formation of thermokarst features, are associated with distinct vegetation and soil moisture changes that lead to abrupt increases in methane emissions, which then are perpetuated through ground surface subsidence and collapse scar bog formation. Current modeling of permafrost peatlands will underestimate carbon emissions from thawing permafrost unless these linkages between plant community, nonlinear active layer dynamics, and carbon fluxes of emerging thaw features are integrated into modeling frameworks.
We present a high-resolution geologic map of the Rubin crater region, located on Mons Amundsen, which has been identified as a promising site for future lunar exploration (AOI E in Wueller et al., 2024). We developed a design reference mission (DRM) to highlight the region's potential for addressing key lunar science goals, particularly those related to the early lunar bombardment history, lunar crustal rocks, volatiles, impact processes at multiple scales, and regolith properties, as outlined by the National Research Council (2007). The Rubin crater, which formed about 1.58 billion years ago during the Eratosthenian period, excavated material from depths of up to 320 m, potentially reaching the underlying South Pole-Aitken (SPA) massif, Mons Amundsen. This makes the crater's ejecta material, along with the Amundsen ejecta covering the massif, prime targets for sampling SPA-derived materials that can expand our understanding of early Solar System dynamics and the lunar cratering chronology. Additionally, the region hosts several permanently shadowed regions (PSRs), ideal for studying potential lunar volatiles and the processes affecting their distribution. The DRM proposes nine traverse options for exploration via walking EVAs, the Lunar Roving Vehicle (LRV), and LRV-assisted EVAs, with traverse lengths ranging from 3.6 km to 18.2 km. Each traverse is designed to sample diverse geologic units and address multiple scientific objectives. Given its scientific potential and favorable exploration conditions, the Rubin crater region is an ideal location for testing south polar landing operations, potentially paving the way for more complex missions, such as a Shackleton crater landing. (c) 2025 The Author(s). Published by Elsevier B.V. on behalf of COSPAR. This is an open access article under the CC BY license (http:// creativecommons.org/licenses/by/4.0/).
Miscanthus is a promising perennial lignocellulosic crop for biomass production. To avoid competing with arable land used for food crops to promote carbon neutrality, cultivating Miscanthus on marginal land, especially in saline soils in China, is a recommended strategy. However, the adaptability of Miscanthus species in saline soil remains largely unknown. In this study, a total of 354 genotypes, including Miscanthus sinensis, Miscanthus floridulus, Miscanthus sacchariflorus, Miscanthus lutarioriparius and interspecific species hybrids derived from M. sinensis and M. lutarioriparius, were evaluated under different planting times (May and August), salinity levels (low and moderate) and pest damage assessment by Helicoverpa armigera in the Yellow River Delta (YRD), in China. The significant effects of planting time on the adaptability of Miscanthus were observed. Planting in May in the YRD, Miscanthus had a lower establishment survival rate (28.76%) and overwintering rate (72.31%), but a dry weight higher than that of planting in August. In contrast, planting in August in the YRD had a very high establishment survival rate (91.14%) and overwintering rate (80.65%), which indicated August was the optimal month for planting Miscanthus in the YRD, while May could be suitable for screening salinity tolerance in Miscanthus. In addition, using the overall adaptability score calculated by establishment survival, overwintering ability, key agronomic traits and pest damage assessments to evaluate all genotypes in this study indicated that the adaptability of M. lutarioriparius was superior to other species. However, M. lutarioriparius is more sensitive to pest damage than others. Furthermore, interspecific hybrids in Miscanthus exhibited outstanding biomass production and adaptability in this region, indicating that creating hybrids would be the best breeding strategy for marginal lands. These results provide an important theoretical basis for the development of Miscanthus in saline soil in the YRD, China.