A comprehensive series of tests, including dynamic triaxial, monotonic triaxial and unconfined compressive strength (UCS) tests, were carried out on reconstituted landfill waste material buried for over twenty years in a closed landfill site in Sydney, Australia. Waste materials collected from the landfill site were treated with varying percentages of cement, and both treated and untreated specimens were investigated to evaluate the influence of cement treatment. The study examined the dynamic properties of cement-treated landfill waste, including cumulative plastic deformation, resilient modulus, and damping ratio, and also analysed the impact of cyclic loading on post-cyclic shear strength in comparison to pre-cyclic shear strength. The UCS tests and monotonic triaxial tests demonstrated that untreated specimens subjected to monotonic loading exhibited a progressive increase in strength with rising axial strain, whereas cement-treated specimens reached a peak strength before experiencing a decline. During cyclic loading, with the inclusion of cement, a significant reduction in cumulative plastic deformation and damping ratio was observed, and this reduction was further enhanced with increasing cement content. Conversely, the resilient modulus showed substantial improvement with the addition of cement, and this enhancement was further amplified with increasing cement content. The formation of cementation bonds between particles curtails particle movement within the landfill waste material matrix and prevents interparticle sliding during cyclic loading, leading to lower plastic strains and damping ratio while increasing resilient modulus. Post-cyclic monotonic testing revealed that cyclic loading caused the partial breakage of the cementation bonds, resulting in reduced shear strength. This reduction was higher on samples treated with lower cement content. Overall, the findings of the research offer crucial insights into the possibility of cement-treated landfill waste as a railway subgrade, laying the groundwork for informed design decisions in developing transport infrastructure over closed landfill sites while using landfill waste materials available on site.

To assess the geotechnical properties of soil, the pressuremeter test has been widely employed since its introduction in 1955. This test is instrumental in determining key parameters such as the limit pressure (Pl), creep pressure (Pf), and modulus of deformation (EM). The fundamental principle of the test involves inserting a radially expandable probe into a borehole, which is subsequently expanded through incremental loading steps, with the resulting volume variation being measured. Traditionally, each loading step is maintained for a duration of 60 s according to European and American standards. In the scope of this study, an investigation was conducted to evaluate the impact of varying the loading time, specifically extending it from 60 to 120 s. These tests were carried out across diverse soil types at four sites in Tunisia. The findings revealed that beyond the 60-s loading period, the soils exhibited continued deformation. Notably, the limit pressure demonstrated a decrease with the prolonged loading time for most of the tested soils. This reduction, ranging from 2% to 30%, was particularly pronounced in soft and sandy clays. Furthermore, the creep pressure, representing the threshold of the soil's pseudoelastic behavior, also experienced a decline with the increased loading time. The pressuremeter modulus EM2, which is obtained for a loading step of Delta t = 120 s, exhibited a reduction across all soil types, with this reduction being more prominent in fine soils characterized by low consistency.

There are currently two main criteria to identify the triggering time of soil liquefaction, namely when the excess pore water pressure reaches vertical effective overburden stress or the double-amplitude axial strain reaches 5 %. However, several researchers have pointed out that the excess pore water pressure may not reach confining pressure at some certain conditions, and the cycle numbers reaching liquefaction obtained by adopting two criteria for calcareous sand specimens are inconsistent, which may lead to overestimation or underestimation of the liquefaction resistance of calcareous sand. Therefore, this study introduces a parameter with physical meaning, secant shear modulus to evaluate the liquefaction potential of soil. To do that, a series of undrained shear tests were conducted on three types of sand. Firstly, the experimental results demonstrated that the difference in cycle numbers to liquefaction obtained by the two criteria increases with the increase of relative density. In addition, the study found that the degradation law of secant shear modulus with the number of cycles is not affected by loading conditions, initial state of soil, and soil type. On this basis, based on the relationship between secant shear modulus gradient and pore pressure ratio, it is highlighted that the liquefaction process can be quantitatively divided into three stages and the moment of liquefaction triggering can be correctly identified. Finally, the proposed liquefaction criterion is compared with widely used traditional criteria and latest apparent viscosity-based criterion, and the results showed that the liquefaction resistance obtained by the proposed criterion was more conservative, which benefits for reducing the occurrence of large strain development.

Lignin fiber is a type of green reinforcing material that can effectively enhance the physical and mechanical properties of sandy soil when mixed into it. In this study, the changes in the dynamic elastic modulus and damping ratio of lignin-fiber-reinforced sandy soil were investigated through vibratory triaxial tests at different lignin fiber content (FC), perimeter pressures and consolidation ratios. The research results showed that FC has a stronger effect on the dynamic elastic modulus and damping ratio at the same cyclic dynamic stress ratio (CSR); with the increase in FC, the dynamic elastic modulus and damping ratio increase and then decrease, showing a pattern of change of the law. Moreover, perimeter pressure has a positive effect on the dynamic elastic modulus, which can be increased by 81.22-130.60 %, while the effect on the damping ratio is slight. The increase in consolidation ratio increases the dynamic elastic modulus by 10.89-30.86 % and the damping ratio by 38.24-100.44 %. Based on the Shen Zhujiang dynamic model, a modified model considering the effect of lignin fiber content FC was established, and the modified model was experimentally verified to have a broader application scope with a maximum error of 5.36 %. This study provides a theoretical basis for the dynamic analysis and engineering applications of lignin-fiber-reinforced sandy soil.

Calcareous sands provide the foundational support for various marine infrastructures. In the harsh marine environment, earthquake or wave loads apply multidirectional cyclic shear stresses to the foundation soil. To explore the undrained multidirectional cyclic response of sand, a series of simple shear tests were performed on reconstituted sand specimens considering the effect of phase difference (theta). By comparing the results with those of siliceous sand under similar conditions, the behavior of calcareous sand under multidirectional cyclic loading became clear. The results demonstrated that calcareous sand shows a lower degree of cyclic instability compared to siliceous sand, corresponding to the weaker strain-softening observed in calcareous sand during monotonic shear tests. The trend in normalized pore water pressure evolution in siliceous sand exceeds that in calcareous sand. Furthermore, under multidirectional cyclic shear conditions, the liquefaction resistance decreases by 30 % in extreme cases, irrespective of sand type. The liquefaction resistance of calcareous sand surpasses that of siliceous sand. However, as the cyclic stress ratio decreases, the reverse trend is observed, regardless of the impact of theta. Subsequently, the possible causes of the above experimental phenomena are explored from the perspectives of shear modulus and energy dissipation.

Due to the detrimental ecological impacts and the exorbitant expenses associated with the cement industry, researchers have sought to find natural, sustainable, low-carbon alternatives to Portland cement for weak soil stabilization. This research used geopolymer based on metakaolin (MK), a natural pozzolanic material with different activator concentrations (NaOH and Na2SiO3), to stabilize loose poorly graded sand soils. The research investigated the effect of different amounts of addition MK (5, 10, and 15 %) on the soil's mechanical properties. Furthermore, the effect of parameters such as the type and concentration of the alkaline solution and curing time (1, 3, and 7 days) on the unconfined compressive strength, failure strain, Young's modulus, California bearing ratio, and direct shear test were evaluated. This research also aims to measure the sub- grade reaction modulus (Ks) by developing and manufacturing a laboratory testing apparatus and steel mold to simulate the natural conditions of sandy subgrade soil obtained from performing nonrepetitive static plate load tests. Additionally, scanning electron microscopy images (SEM) and X-ray diffraction analysis (XRD) were also used to study the microstructural changes and the chemical composition of the stabilized soil samples. The results indicate that the soil samples that were stabilized with MK 10 % and NaOH had notably higher compressive strength (2936 kPa), indicating a denser and less porous structure (improved stiffness stabilized soil) in comparison to the soil samples stabilized with MK 10 % and Na2SiO3 which was (447 kPa). Ultimately, Microstructural analysis showed that, due to the addition of 10 % MK, stabilized soils have a denser and more homogeneous structure.

In this study, we present an on-chip analytical method using a microfluidic device to characterize the mechanical properties in growing roots. Roots are essential organs for plants and grow under heterogeneous conditions in soil. Especially, the mechanical impedance in soil significantly affects root growth. Understanding the mechanical properties of roots and the physical interactions between roots and soil is important in plant science and agriculture. However, an effective method for directly evaluating the mechanical properties of growing roots has not been established. To overcome this technical issue, we developed a polydimethylsiloxane (PDMS) microfluidic device integrated with a cantilevered sensing pillar for measuring the protrusive force generated by the growing roots. Using the developed device, we analyzed the mechanical properties of the roots in a model plant, Arabidopsis thaliana. The root growth behavior and the mechanical interaction with the sensing pillar were recorded using a time-lapse microscopy system. We successfully quantified the mechanical properties of growing roots including the protrusive force and apparent Young's modulus based on a simple physical model considering the root morphology. (c) 2025 Institute of Electrical Engineers of Japan and Wiley Periodicals LLC.

Stone columns are a resultful measure to increase the bearing capacity of soft or liquefiable foundations. The centrifuge model test and finite element method were employed to investigate the bearing capacity and deformation behavior of the stone column-reinforced foundation. Study shows that the modulus of the reinforced foundation exhibits significant anisotropy. A bulging deformation area is identified in the reinforced foundation where obvious horizontal deformation of the stone column occurs. The ratio of the column stress and soil stress is observed to change violently in this area. A homogenization technique is consequently deduced by employing the column-soil stress ratio as a key variable. The definition of the column-soil stress ratio is extended to reasonably describe the column-soil interaction under different stress levels and its approximation method is given. Based on the Duncan- Chang E-nu model, a simplified method using the homogenization technique is proposed for the stone column reinforced foundation. The proposed homogenization technique and simplified method have been validated by the centrifuge model tests and finite element analyses. This method properly addresses the nonlinear spatial characteristic of deformation and the anisotropy of the stone column reinforced foundation.

A large diameter triaxial specimen of 61.9 mm was made by mixing coconut shell fibers with red clay soil. The shear strength of coconut shell fiber-reinforced soil was investigated using a dynamic triaxial shear test with confining pressure in a range of 50-250 kPa, a fiber content of 0.1%-0.5%, and a loading frequency of 0.5-2.5 Hz. The Hardin-Drnevich model based on the coconut shell fiber-reinforced soil was developed by analyzing and processing the experimental data using a linear fitting method, determining the model parameters a and b, and combining the influencing factors of the coconut shell fiber-reinforced soil to improve the Hardin-Drnevich model. The results show a clear distinction between the effects of loading frequency and fiber content on the strength of the specimens, which are around 1 Hz and 0.3%, respectively. Hardin-Drnevich model based on coconut shell fiber-reinforced soil can better predict the dynamic stress-strain relationship of coconut shell fiber-reinforced soil and reflect the dynamic stress-strain curve characteristics of the dynamic stress-strain curve coconut shell fiber-reinforced soil.

Cemented sand-gravel (CSG) is an innovative material for dam construction with a wide range of applications. Nevertheless, a comprehensive understanding of the dynamic properties of CSG is lacking. A series of cyclic triaxial dynamic shear tests were carried out on CSG materials to investigate their complex dynamic mechanical properties, leading to the establishment of a dynamic constitutive model considering damage. The findings indicate that both the application of confining pressure and the addition of cementitious material have a noticeable influence on the morphology of the hysteresis curve. Further research scrutiny reveals that augmenting confining pressure and gel content leads to an increase in the dynamic shear modulus and a decrease in damping ratio. Furthermore, a constitutive dynamic damage constitutive model was constructed by linking a damage element to the generalized Kelvin model and defining the damage variable D based on energy interaction principles. The theoretical formulas for dynamic shear modulus and damping ratio were adjusted accordingly. In addition, the stiffness matrix of the dynamic damage constitutive model was derived, which demonstrated its strong fitting effects in dynamic triaxial shear tests on CSG. Finally, the dynamic response and damage distribution in the dam body under dynamic loading were analyzed using a selected CSG dam in China.