The overconsolidation ratio (OCR) is a critical factor in determining the mechanical behaviour of overconsolidated clays. On the basis of the three requirements for the peak strength line, a continuous and smooth peak strength line is constructed from the perspective of the peak stress ratio, and then a new yield function for overconsolidated clays is developed. The developed yield function in the stress space is characterized by an elliptical curve. The evolution of the developed yield function in the stress space is captured by a new hardening parameter, which is constructed by integrating the proposed peak strength surface with the subloading surface concept. By combining the developed yield function with the non-orthogonal plastic flow rule, a non-orthogonal elastoplastic constitutive model of overconsolidated clays is established to consider the influence of the OCR on strength and deformation. The proposed model requires seven material parameters, all of which have a clear physical meaning and can be easily determined via conventional laboratory tests. Three typical stress paths are employed to demonstrate the essential features of the proposed model. The effectiveness of the proposed model is confirmed by comparing the experimental data with corresponding model predictions.

Aeolian sand along the Hojiakueri Railway in the Taklimakan Desert exhibits poor mechanical properties for direct use as a filler for railway subgrades. Although cemented soil reinforced with single fibers can improve mechanical properties, its limited effectiveness and high cement usage pose significant economic and environmental concerns. This study investigated the improvement of splitting tensile strength (STS) in cemented aeolian sand through hybrid fiber reinforcement. An orthogonal test was designed to evaluate four factors-fiber types (pairwise combinations of basalt, polypropylene, and glass fibers), fiber lengths (3, 6, and 9 mm), hybridization ratios (1:1, 1:3, and 3:1), and fiber contents (4 %o, 8 %o, and 12 %o) - along with their interactions. The performance of cemented aeolian sand reinforced with hybrid fiber (CASRHF) was evaluated through STS tests and scanning electron microscopy (SEM). The results identified the optimal combination as a 1:1 mix of 6 mm basalt and polypropylene fibers with a fiber content of 12 %o. The interaction between hybrid fiber type and fiber length was the most critical factor influencing STS, followed by hybrid fiber type, fiber length, and fiber content. SEM analysis further revealed a linear negative correlation between STS and porosity, providing new insights into the microscopic mechanisms. The findings underscore the importance of optimizing hybrid fiber combinations to meet the performance requirements of railway subgrade beds in aeolian sand regions.

Cohesion provided by pore ice is a critical component influencing the mechanical behavior of frozen soil, as it not only cements soil particles together but also shares the external loads with them. In view the crucial role of cohesion in developing an elastoplastic model for frozen soil, this paper employs triaxial tensile strength (TTS) to characterize cohesion and proposes a TTS degradation expression driven by plastic shear strain. By directly incorporating TTS into the yield function, a framework for a Non-Orthogonal Elastoplastic (NOEP) constitutive model that accounts for cohesion degradation in frozen soil is developed. Furthermore, a hardening parameter incorporating TTS is introduced and used in conjunction with the modified yield function to determine the magnitude of the plastic strain increment. The non-orthogonal plastic flow rule is used to determine the direction of the plastic strain increment based on the modified yield function. Ultimately, by combining the elastic strain increment determined by Hooke's rule, a NOEP constitutive model incorporating cohesion degradation for frozen soil is established. The validity and rationality of the proposed NOEP model in representing the stress-strain relationship of frozen soil are confirmed through comparisons with test results of frozen soil under the triaxial compression conditions. The proposed constitutive model provides a more comprehensive and precise representation of frozen soil's response to external loading, enhancing the understanding of its shear deformation behavior and providing a robust theoretical foundation for engineering design and construction in cold regions.

In order to study the cement-industrial waste-based synergistic curing of silt soil, orthogonal design tests were used to prepare a new curing agent using cement, fly ash, blast furnace slag, and phosphogypsum as curing materials. In order to evaluate the cement-industrial waste-cured soils, unconfined compressive strength tests, fluidity tests, wet and dry cycle tests, and electron microscope scanning tests were carried out. The mechanical properties and microstructure of the cement-industrial slag were revealed and used to analyze the curing mechanism. The results showed that, among the cement-industrial wastes, cement and blast furnace slag had a significant effect on the unconfined compressive strength of the specimens, and the optimal ratio for early strength was cement-fly ash-slag-phosphogypsum = 1:0.11:0.44:0.06; the optimal ratio for late strength was cement-fly ash-slag-phosphogypsum = 1:0.44:0.44:0.06. In the case of a 140% water content, the 28d compressive strengths of curing agent Ratios I and II were 550.3 kPa and 586.5 kPa, respectively. When a polycarboxylic acid water-reducing agent was mixed at 6.4%, the mobilities of curing agent Ratios I and II increased by 32.1% and 35.8%, and the 28d compressive strengths were 504.1 kPa and 548.8 kPa, respectively. When calcium chloride was incorporated at 1.5%, the early strength of the cured soil increased by 33% and 29.1% compared to that of the unadulterated case year on year, and the mobility was almost unchanged. From microanalysis, it was found that the cement-industrial waste produced the expansion hydration products calcium alumina (AFt) and calcium silicate (C-S-H) during the hydration process. The results of this study provide a certain basis and reference value for the use of marine soft soil as a fluid filling material.

The application of alkali-activated slag (AAS) cementing material to the curing of soft soil foundations has a good engineering application prospect and is economical and environmentally friendly. In this study, three different activators (Na2OnSiO(2), NaOH, Ca(OH)(2)) were used to alkali-activate slag powder to solidify and improve soft soil in inland port areas. In order to explore the mechanical properties and strength formation mechanism of AAS-solidified soil under different activators, mechanical properties, and microscopic tests were carried out. Firstly, with unconfined compressive strength as the evaluation index, an orthogonal test of three factors, such as the type of activator, the amount of activator, and the amount of slag powder, was designed. Then, the unconfined compressive strength, resilience modulus, shear strength, and compression modulus of AAS-solidified soil were tested with the three activators under optimal dosage. Finally, phase composition, SEM-EDS, TG-DTG, and FT-IR analyses were carried out with the three AAS-solidified soils. The results show the following: (1) The factors affecting the unconfined compressive strength of AAS-solidified soil are ordered as follows: the type of activator > the amount of activator > the amount of slag powder. In addition, the optimal factors were as follows: activator type: Na2OnSiO(2); amount of activator: 3%; and amount of slag powder: 20%. (2) In considering the macroscopic mechanical properties, the effect of the activator is Na2OnSiO(2) > NaOH > Ca(OH)(2), and the Na2OnSiO(2) AAS-solidified soil has good early strength. (3) The hydration products of AAS are mainly C-A-S-H gel, N-A-S-H gel, and C-S-H gel, which increase the strength and cohesion of solidified soil. The results show that AAS-solidified soil with 0.7-modulus Na2OnSiO(2) as the activator has good engineering characteristics and can be used for curing soft soil foundations.

To the aim of this paper is to study the structural and environmental deformation characteristics caused by the excavation of a very large deep foundation pit in the sandy soil area of Beijing. This paper is based on numerical simulation and field monitoring results and these results are compared with the deformation data of a soft soil foundation pit in the Shanghai area. The results show that the influence of the environment surrounding the super-large deep foundation pit project studied in this paper is obviously too great. With the progress of construction, the deformation rate and deformation amount of the column at the side of the foundation pit are obviously higher than that of the column in the middle area. Due to the hysteresis of stress transfer in the sand, the settlement of the roof of the north wall is delayed and the deformation range is smaller than that of the south wall. Compared with the conventional foundation pit, the influence area of the surrounding surface is larger, reaching 4 He (He is the depth of the foundation pit). Delta vmax (the maximum surface settlement) is between 0.2 similar to 2.3% He, and the relationship between delta vmax = 1.43% Vwm. Through orthogonal experiments and numerical simulation, it is concluded that the deformation of foundation pit structure and its surrounding environment is more sensitive to excavation unloading, precipitation amplitude, and column spacing. It is also concluded that the strong, medium, and weak influence areas of the bottom uplift after foundation pit construction are (0 similar to 0.07) x L, (0.07 similar to 0.14) x L, and (0.14 similar to 0.5) x L, respectively (L is the width of foundation pit). When the embedment ratio is between 1.8 similar to 2.4, the displacement mode of the parapet structure is T mode; when the embedment ratio is between 2.4 similar to 3.4, the displacement mode of the parapet structure is RB mode.

This study investigates the collision model of cassava seed stems in precision planters. Utilizing a physical property analyzer and a custom test platform based on collision dynamics principles, we measured and analyzed the forces and recovery coefficients of seed stem collisions. Mixed orthogonal and one-way tests were conducted to identify the main factors affecting the collision recovery coefficient of seed stems, including collision contact material, drop height, seed stem mass, moisture content, drop direction, and seed stem variety. The results from the orthogonal tests indicated that the factors influencing the collision recovery coefficient were ranked as follows: collision contact material > drop height > seed stem mass > moisture content > drop direction > seed stem variety. Notably, the effects of impact contact material, drop height, stem mass, and moisture content were significant, while the effects of drop direction and seed stem variety were relatively insignificant. The one-way test results revealed that the collision recovery coefficients for cassava seed stems with structural steel Q235, rubber sheet, seed stems, and sandy loam soil decreased progressively, with values for SC205 being 0.8172, 0.6975, 0.6649, and 0.6341, respectively, and values for GR4 being 0.7796, 0.7132, 0.6913, and 0.6134, respectively. Furthermore, as drop height increased, the collision recovery coefficient of cassava seed stems decreased; similarly, higher stem mass and moisture content correlated with lower coefficients. To minimize impact during critical stages of cassava planting, transportation, and processing, materials with lower recovery coefficients should be prioritized in equipment design. Incorporating rubber coatings can effectively mitigate collision effects in components such as seed supply and planting mechanisms. These findings provide valuable insights for designing and enhancing key mechanical features in machinery used for planting, transporting, and processing cassava.

This study aimed to address the challenges of solid waste utilization, cost reduction, and carbon reduction in the treatment of deep-dredged soil at Xuwei Port in Lianyungang city of China. Past research in this area was limited. Therefore, a curing agent made from powdered shells was used to solidify the dredged soil in situ. We employed laboratory orthogonal tests to investigate the physical and mechanical properties of the powdered shell-based curing agent. Data was collected by conducting experiments to assess the role of powdered shells in the curing process and to determine the optimal ratios of powdered shells to solidified soil for different purposes. The development of strength in solidified soil was studied in both seawater and pure water conditions. The study revealed that the strength of the solidified soil was influenced by the substitution rate of powdered shells and their interaction with cement. Higher cement content had a positive effect on strength. For high-strength solidified soil, the recommended ratio of wet soil: cement: lime: powdered shells were 100:16:4:4, while for low-strength solidified soil, the recommended ratio was 100:5.4:2.4:0.6. Seawater, under appropriate conditions, improved short-term strength by promoting the formation of expansive ettringite minerals that contributed to cementation and precipitation. These findings suggest that the combination of cement and powdered shells is synergistic, positively affecting the strength of solidified soil. The recommended ratios provide practical guidance for achieving desired strength levels while considering factors such as cost and carbon emissions. The role of seawater in enhancing short-term strength through crystal formation is noteworthy and can be advantageous for certain applications. In conclusion, this research demonstrates the potential of using a powdered shell-based curing agent for solidifying dredged soil in an environmentally friendly and cost-effective manner. The recommended ratios for different strength requirements offer valuable insights for practical applications in the field of soil treatment, contributing to sustainable and efficient solutions for soil management.

In deep foundation pit engineering, the soil undergoes a complex stress path, encompassing both loading and unloading phases. The Shanghai model, an advanced constitutive model, effectively accounts for the soil's deformation characteristics under these varied stress paths, which is essential for accurately predicting the horizontal displacement and surface settlement of the foundation pit's enclosure structure. This model comprises eight material parameters, three initial state parameters, and one small-strain parameter. Despite its sophistication, there is a scarcity of numerical studies exploring the correlation between these parameters and the deformation patterns in foundation pit engineering. This paper initially establishes the superiority of the Shanghai model in ultra-deep circular vertical shaft foundation pit engineering by examining a case study of a nursery circular ultra-deep vertical shaft foundation pit, which is part of the Suzhou River section's deep drainage and storage pipeline system pilot project in Shanghai. Subsequently, utilizing an idealized foundation pit engineering model, a comprehensive sensitivity analysis of the Shanghai model's multi-parameter values across their full range was performed using orthogonal experiments. The findings revealed that the parameter most sensitive to the lateral displacement of the underground continuous wall was kappa, with an increase in kappa leading to a corresponding increase in displacement. Similarly, the parameter most sensitive to surface subsidence outside the pit was lambda, with an increase in lambda resulting in greater subsidence. Lastly, the parameter most sensitive to soil uplift at the bottom of the pit was also kappa, with an increase in kappa leading to more significant uplift.

To improve the utilization rates of soda residue (SR) and fly ash (FA), reduce environmental pollution, and enhance the mechanical properties of marine clay (MC), this study proposes mixing SR, FA, and MC with cement and /or lime to prepare soda residue-fly ash stabilized soil (SRFSS). Using an orthogonal design for the proportions, the study analyzes the compaction performance, unconfined compressive strength (UCS), and shear strength of SRFSS. The influence of various factors on the mechanical properties of SRFSS was investigated through range and variance analyses. The mechanical mechanism was revealed from the perspectives of grading and cementation. The results indicate that SR and FA significantly impact the mechanical properties of SRFSS. The range and variance analysis results are consistent: SR content of 30% and 70% has the most significant impact on compaction performance and UCS, respectively, while 20% FA content has the greatest effect on shear strength. The recommended base proportion is 70% SR + 20% FA + 10% MC. The gradation and cementitious properties jointly influence the mechanical performance and microstructure of SRFSS, G8 has the lowest planar porosity, at only 0.89%. The calcium (Ca) content in SRFSS specimens with different proportions shows significant variation, from 5.0 to 53.6 wt%, while the silicon (Si)/Al ratio (0.76-2.73) shows relatively small fluctuations. The primary hydration products include calcium hydroxide (Ca(OH)2), calcium silicate hydrate (C-S-H), and ettringite (AFt).