Aeolian sand along the Hojiakueri Railway in the Taklimakan Desert exhibits poor mechanical properties for direct use as a filler for railway subgrades. Although cemented soil reinforced with single fibers can improve mechanical properties, its limited effectiveness and high cement usage pose significant economic and environmental concerns. This study investigated the improvement of splitting tensile strength (STS) in cemented aeolian sand through hybrid fiber reinforcement. An orthogonal test was designed to evaluate four factors-fiber types (pairwise combinations of basalt, polypropylene, and glass fibers), fiber lengths (3, 6, and 9 mm), hybridization ratios (1:1, 1:3, and 3:1), and fiber contents (4 %o, 8 %o, and 12 %o) - along with their interactions. The performance of cemented aeolian sand reinforced with hybrid fiber (CASRHF) was evaluated through STS tests and scanning electron microscopy (SEM). The results identified the optimal combination as a 1:1 mix of 6 mm basalt and polypropylene fibers with a fiber content of 12 %o. The interaction between hybrid fiber type and fiber length was the most critical factor influencing STS, followed by hybrid fiber type, fiber length, and fiber content. SEM analysis further revealed a linear negative correlation between STS and porosity, providing new insights into the microscopic mechanisms. The findings underscore the importance of optimizing hybrid fiber combinations to meet the performance requirements of railway subgrade beds in aeolian sand regions.

Limestone calcined clay cement (LC3) is now about to become a new type of cement. Replacing a considerable part of cement with calcined clay makes the new cement more sustainable than ordinary Portland cement. In this investigation, locally available non-kaolinite clayey soil is studied in two stages. Firstly, the calcined temperature, the replacement level of calcined clay, and the ratio of the calcined clay to limestone were optimized. The results were 750 degrees C, 40%, and 3:1, respectively. The optimized mixtures were reinforced with recycled polyethylene terephthalate (PET) and polypropylene (PP) fibers at ratios of 0%, 0.5%, 1%, and 1.5% of the binder's weight. Flowability was measured for the fresh mortar. Mechanical properties such as compressive strength, flexural strength, and splitting tensile strength were studied. Durability properties like fire resistance, water absorption, water sorptivity, and porosity were examined. The results show that 1.5% of PET fiber and 1% of PP fiber showed the best results in terms of mechanical and durability properties. Flexural strength increased from 6.35 to 8.45 MPa and to 7.52 MPa when PP and PET fiber were increased from 0 to 1 and 1.5% respectively. Similarly, tensile strength increased from 3.78 to 4.25 MPa and to 5.25 MPa when PP and PET fiber were increased from 0 to 1.5% and 1%, respectively. However, increasing fibers consistently decreased flowability. This investigation demonstrates the potential of using the locally available non-kaolinite clayey soil to be used as pozzolanic material and to produce LC3. Consequently, LC3 shows the potential to use as a structural material.

Adding fibers into cement to form fiber-reinforced soil cement material can effectively enhance its physical and mechanical properties. In order to investigate the effect of fiber type and dosage on the strength of fiber-reinforced soil cement, polypropylene fibers (PPFs), polyvinyl alcohol fibers (PVAFs), and glass fibers (GFs) were blended according to the mass fraction of the mixture of cement and dry soil (0.5%, 1%, 1.5%, and 2%). Unconfined compressive strength tests, split tensile strength tests, scanning electron microscopy (SEM) tests, and mercury intrusion porosimetry (MIP) pore structure analysis tests were conducted. The results indicated that the unconfined compressive strength of the three types of fiber-reinforced soil cement peaked at a fiber dosage of 0.5%, registering 26.72 MPa, 27.49 MPa, and 27.67 MPa, respectively. The split tensile strength of all three fiber-reinforced soil cement variants reached their maximum at a 1.5% fiber dosage, recording 2.29 MPa, 2.34 MPa, and 2.27 MPa, respectively. The predominant pore sizes in all three fiber-reinforced soil cement specimens ranged from 10 nm to 100 nm. Furthermore, analysis from the perspective of energy evolution revealed that a moderate fiber dosage can minimize energy loss. This paper demonstrates that the unconfined compressive strength test, split tensile strength test, scanning electron microscopy (SEM), and mercury intrusion porosimetry (MIP) pore structure analysis offer theoretical underpinnings for the utilization of fiber-reinforced soil cement in helical pile core stiffening and broader engineering applications.

Cement production in the world market is steadily increasing. In 2000, it was 1600 million tons, while as of 2013, the annual amount exceeded 4000 million tons. The burning of cement clinker is associated with the generation of waste. It is estimated that the amount of cement kiln dust (CKD), during combustion, reaches about 15-20%, which means 700 million tons per year. However, not all types of by-products are reusable due to high alkali, sulfate, and chloride contents, which can adversely affect the environment. One environmentally friendly solution may be to use CKD in the production of high-performance concrete (HPC), as a substitute for some of the cement. This paper presents a study of the short- and long-term physical and mechanical properties of HPC with 5%, 10%, 15%, and 20% CKD additives. The experiments determined density, water absorption, porosity, splitting tensile strength, compressive strength, modulus of elasticity, ultrasonic pulse velocity, and evaluated the microstructure of the concrete. The addition of CKD up to 10% caused an increase in the 28- and 730-day compressive strengths, while the values decreased slightly when CKD concentration increased to 20%. Splitting tensile strength decreased proportionally with 5-20% amounts of CKD regardless of HPC age. Porosity, absorbability, and ultrasonic pulse velocity decreased with increasing cement dust, while the bulk density increased for HPC with CKD. Microstructure analyses showed a decrease in the content of calcium silicate hydrate (C-S-H), acceleration of setting, and formation of wider microcracks with an increase in CKD. From the results, it was shown that a 15% percentage addition of CKD can effectively replace cement in the production of HPC and contribute to reducing the amount of by-product from the burning of cement clinker.