Uneven displacement of permafrost has become a major concern in cold regions, particularly under repeated freezing-thawing cycles. This issue poses a significant geohazard, jeopardizing the safety of transportation infrastructure. Statistical analyses of thermal penetration suggest that the problem is likely to intensify as water erosion expands, with increasing occurrences of uneven displacement. To tackle the challenges related to mechanical behavior under cyclic loading, the New Geocell Soil System has been implemented to mitigate hydrothermal effects. Assessment results indicate that the New Geocell Soil System is stable and effective, offering advantages in controlling weak zones on connecting slopes and reducing uneven solar radiation. Consequently, the New Geocell Soil System provides valuable insights into the quality of embankments and ensures operational safety by maintaining displacement at an even level below 1.0 mm. The thermal gradient is positive, with displacement below 6 degrees C/m, serving as a framework for understanding the stability of the subgrade. This system also enhances stress and release the sealing phenomenon.

In order to investigate the frost-heaving characteristics of wintering foundation pits in the seasonal frozen ground area, an outdoor in-situ test of wintering foundation pits was carried out to study the changing rules of horizontal frost heave forces, vertical frost heave forces, vertical displacement, and horizontal displacement of the tops of the supporting piles under the effect of groundwater and natural winterization. Based on the monitoring condition data of the in-situ test and the data, a coupled numerical model integrating hydrothermal and mechanical interactions of the foundation pit, considering the groundwater level and phase change, was established and verified by numerical simulation. The research results show that in the silty clay-sandy soil strata with water replenishment conditions and the all-silty clay strata without water replenishment conditions, the horizontal frost heave force presents a distribution feature of being larger in the middle and smaller on both sides in the early stage of overwintering. With the extension of freezing time, the horizontal frost heave force distribution of silty clay-sand strata gradually changes from the initial form to the Z shape, while the all-silty clay strata maintain the original distribution characteristics unchanged. Meanwhile, the peak point of the horizontal frost heave force in the all-silty clay stratum will gradually shift downward during the overwintering process. This phenomenon corresponds to the stage when the horizontal displacement of the pile top enters a stable and fluctuating phase. Based on the monitoring conditions of the in-situ test, a numerical model of the hydro-thermo-mechanical coupling in the overwintering foundation pit was established, considering the effects of the groundwater level and ice-water phase change. The accuracy and reliability of the model were verified by comparison with the monitoring data of the in-situ test using FLAC3D finite element analysis software. The evolution of the horizontal frost heaving force of the overwintering foundation pit and the change rule of its distribution pattern under different groundwater level conditions are revealed. This research can provide a reference for the prevention of frost heave damage and safety design of foundation pit engineering in seasonal frozen soil areas.

The thermo-mechanical (TM) behaviour of the energy pile (EP) group becomes more complicated in the presence of seepage, and the mechanism by which seepage impacts the EP group remains unclear.In the current work, a 2 x 2 scale model test bench of EP group was set up to investigate the TM behaviour of EP group with seepage. The test results indicate that the heat exchange performance of EP group with seepage can be significantly enhanced, but also leads to obvious differences in the temperature distribution of pile and surrounding soil along the seepage direction, and thus causes evident differences in the mechanical properties between the front pile and the back pile in pile group. Compared with the parallel connection form, the thermal performance of EP group with the series connection form is slightly attenuated. However, the mechanical properties of various piles in the EP group differ significantly. Under the action of seepage, the mechanical balance properties of various piles in the forward series form are optimal, followed by the parallel form, and the reverse series form is the least optimal. A 3-D CFD model was established to further obtain the influence of seepage and arrangement forms on EP group. The findings indicate that seepage can not only mitigate thermal interference between distinct piles but also expedite the process of heat transfer from pile-soil to reach a state of stability. Concurrently, the thermal migration effect induced by seepage will be superimposed along the seepage direction, resulting in the elevation of thermal interference of each pile along the seepage direction, and the superposition of thermal migration effect increases with the time. Under the same seepage condition, the cross arrangement can enhance the thermal performance of EP group, optimize the temperature distribution of pile and soil, and thus the imbalance of mechanical properties among pile groups can be reduced. In addition, the concepts of thermal interference coefficient and heat exchange rate per unit soil volume are introduced to facilitate a more precise evaluation of the thermal interference degree of each pile in the pile group and the heat exchange performance under different pile arrangement forms.The standard deviation and mean value in the statistical method are used to evaluate the equilibrium of mechanical properties of pile group, which is more intuitive to compare the differences in mechanical properties of pile groups under different working conditions.

Composed of a raft and pipe piles with embedded heat exchange devices, a pipe-type energy piled raft foundation can enhance both foundation performance and energy utilization efficiency. An urgently needed thermomechanical analysis method would facilitate the optimization design and the broader adoption of this fundamental form. Therefore, this paper proposes an efficient method for the thermo-mechanical analysis of pipe-type energy piles with a raft in layered transversely isotropic media. The pile-soil and raft-soil interaction equations are derived by coupled finite and boundary element method. A simplified approach is then proposed and applied to tackle the pile-raft-soil coupling interaction. The correctness and efficiency of the method are verified through comparisons with a field test and two finite element numerical cases. Finally, parametric analyses are conducted to investigate the influences of temperature increment, pile thickness, raft thickness, and soil anisotropy on the performance of the pipe-type energy piled raft foundation.

The majority of existing effective stress-based constitutive models approach thermal effects through the temperature dependency of surface tension and its effects on the soil-water retention curve (SWRC) and effective stress. Experimental tests and theoretical studies, however, suggest that the temperature effect on surface tension alone is not sufficient to properly explain thermal-induced changes in the effective stress and SWRC. This study focuses on the temperature-dependent elastoplastic behavior of low plasticity unsaturated soils by developing a set of constitutive-level relations that incorporate temperature-dependent SWRC and effective stress models. These models account for the effect of temperature on the enthalpy, contact angle, and surface tension. The application of the presented constitutive relations was demonstrated and validated for low plasticity soils, specifically incorporating temperature effects into the hardening modulus, specific volume change, yield stress of the modified Cam-Clay model, and stress-strain relationships. The proposed relationships are incorporated in any effective stress-based constitutive model for modeling temperature dependency of elastoplastic response in low plasticity unsaturated soils. Employing these relationships can enhance the numerical simulation of low plasticity unsaturated soils under thermo-mechanical or other coupled processes involving temperature-dependent conditions.

The effect of the load level on long-term thermally induced pile displacements and the impact of cyclic thermal loads on the bearing capacity of energy piles are investigated via a full-scale in situ test in Delft, The Netherlands. The pile was loaded to a specific target of 0, 30, 40, or 60% of its calculated ultimate bearing capacity. At the end of each loading step, up to ten cooling-natural heating cycles were applied. The pile behavior during monotonic cooling and cyclic cooling-natural heating in terms of the displacement along the pile is reported, with a focus on permanent displacements. During monotonic (pile/ground) cooling, a settlement of the pile head and an uplift of the pile segment near the pile tip were observed in all four tests. In addition, under higher mechanical load, the pile head displacement was larger while the uplift was lower due to the imposed mechanical load. During cyclic thermal load, under zero mechanical load, pile head displacement was fully reversible while permanent uplift of the lowest pile segment was observed and attributed mainly to the permanent dragdown of the surrounding soil. Under moderate mechanical loads (30 and 40%), thermal cycles induced an irreversible pile head settlement, which stabilized with an increasing number of cycles. In addition, a permanent pile settlement along the pile was observed at the end of these tests. Under high mechanical load (60%), the irreversible settlement along the pile continued to increase with only a slight reduction in rate, being higher compared to moderate mechanical loads. In this test, a normalized pile head settlement of 0.124% was observed after ten thermal cycles. The permanent settlement of the pile under thermo-mechanical loads was mainly attributed to the contraction of sand beneath the pile tip and thermal creep at the soil-structure interface. The pile bearing capacity was observed to increase after thermo-mechanical tests, mainly due to the residual/plastic pile head displacement, which in turn densified sand leading to an increase in tip resistance.

The operational performance of energy pile (EP) group with seepage is strongly influenced by seepage parameters. In this paper, a model test system of 2 x 2 EP group with seepage is built to study the influences of seepage water level and seepage velocity on thermo-mechanical behaviour of EP group. Also, a numerical model of EP group considering seepage is developed to obtain the variations of thermo-mechanical behaviour of EP group under different seepage parameters. The findings demonstrate that an augmentation in seepage water level can enhance the heat exchange performance of EP group, but it also exacerbate the imbalance of mechanical properties between piles in the short term, in which the seepage only have a significant effect on the temperature of piles and soil below the seepage water level. Increasing seepage velocity and circulating flow rate can strengthen thermal performance of EP group and improve the equilibrium of pile axial force and displacement between the pile groups, but increasing seepage velocity also increases the imbalance of mechanical properties between the front and back rows of pile group. At the same time, compared to the circulating flow rate, the change in seepage velocity has a dominant impact on the thermo-mechanical characteristics of EP group. Moreover, when the seepage angle is within 0-45 degrees, increasing the seepage angle can effectively improve the heat transfer performance of EP group, and the temperature distribution of pile and soil is obviously different for different seepage angles, in which the mechanical properties of EP group have the best equilibrium when the seepage angle is 30 degrees for current simulation conditions.

It is a fact that the temperature inside the waste mass is higher than the ambient outside the landfill. However, only a few experimental works have tried to address the effect of such elevated temperatures on the mechanical behavior of waste. Accordingly, developing a constitutive model based on experimental achievement is still incipient. In this paper, results from experimental literature and the results of a complementary testing campaign aided in better understanding and modeling the waste thermo-mechanical behavior. An existing model framework by the authors is extended to incorporate thermal effects on the waste bulk and fibrous reinforcement particles. The model predicted fairly the mechanical behavior of waste in terms of deviatoric stress, pore water pressure, and volumetric strains in drained and undrained triaxial tests performed on samples at different temperatures and with different plastic contents. Values of deviatoric stress predicted by the model for two specific axial strains are compared with experimental results, considering all the tested samples, proving the model's capabilities in reproducing the waste's overall behavior. Considering an axial strain of 20%, the probabilities of the model error occurrence in the range of +/- 25% are 55% and 67% for CIU and CID tests, respectively.

BackgroundThe dynamic coupled hydro-thermo-mechanical behavior of the unlined structure in saturated porous structure under extreme geotechnical and geology engineering (e.g., underground explosion, laser thermal rock breaking) have aroused extensive research interests on the constitutive modeling and transient dynamic responses prediction. Although the current fractional-order hydro-thermo-mechanical models have been historically proposed, the theoretical formulations still adopt the classical fractional derivatives with singular kernels, and the inherent strain relaxation effect and the associated memory dependency remains not considered yet in such complex condition.PurposeTo compensate for such deficiencies, the current work aims to establish the new hydro-thermo-mechanical model by introducing the Atangana-Baleanu (AB) and Tempered-Caputo (TC) fractional derivatives with non-singular kernels.MethodsThe proposed model is applied to investigate transient structural dynamic hydro-thermo-mechanical response of a cylindrical unlined tunnel in poroelastic medium by applying Laplace transformation approach.ResultsThe influences of the AB and TC fractional derivatives on the wave propagations as well as the dimensionless responses of the temperature, displacement, stress, and pore-water pressure are evaluated and discussed.ConclusionThe non-singular AB and TC fractional derivatives slower the thermal wave propagation. In addition, the dimensionless pore water pressure dissipation is maximally reduced. The increase of strain relaxation time parameter reduces the mechanical dynamic response regions and eliminates the sharp jumps of mechanical response at the elastic wave front, which are consistent with continuity of displacement in real engineering situations.

This paper presents a study on model tests of single energy piles subjected to cyclic axial loads in sand and the development and validation of a 3D thermo-mechanical finite element model. The model accurately simulated the behavior of the pile-soil interface under cyclic shear loads. A subsequent parametric analysis examined the effects of the number of loading cycles and the loading amplitude on the vertical dynamic response characteristics of energy piles. The results showed that under heating conditions, the maximum variation in compressive thermal stress in the energy pile gradually decreased, with its location shifting upward along the pile shaft. A critical cyclic amplitude ratio was identified: below this threshold, the rate of increase in pile tip resistance continuously increased while the average pile side resistance weakened progressively. The presence of a static load accelerated the weakening of the average pile side resistance to some extent. As the number of loading cycles increased, the settlement rate of the energy pile gradually degraded. The cumulative settlement rate at the pile top increased with the cyclic amplitude ratio, peaking before slightly declining. In comparison, the static load ratio had a relatively minor influence on cumulative settlement.