Most gravel roads leading to rural areas in Ghana have soft spot sections as a result of weak lateritic subgrade layers. This study presents a laboratory investigation on a typical weak lateritic subgrade soil reinforced with non-woven fibers. The objective was to investigate the strength characteristic of the soil reinforced with non-woven fibers. The California Bearing Ratio and Unconfined Compressive Strength tests were conducted by placing the fibers in single layer and also in multiple layers. The results showed an improved strength of the soil from a CBR value of 7%. The CBR recorded maximum values of 30% and 21% for coconut and palm fibers inclusion at a placement depth of H/5 from the compacted surface. Multiple fiber layer application at depths of H/5 & 2 h/5 yielded CBR values of 38% and 31% for coconut and palm fibers respectively. The Giroud and Noiray design method and the Indian Road Congress design method recorded reduction in the thickness of pavement of 56% to 63% for coconut fiber inclusion and 45% to 55% for palm fiber inclusion. Two-way statistical analysis of variance (ANOVA) showed significant effect of depth of fiber placement and fiber type on the geotechnical characteristics considered. (sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic),(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic). (sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic). (sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic). (sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic). (sic)(sic)(sic)(sic),CBR(sic)(sic)7%(sic),(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic). (sic)(sic)(sic)(sic)(sic)(sic)(sic)H/5(sic)(sic)(sic)(sic)(sic)(sic),CBR(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)30%(sic)21%. (sic)H/5(sic)2H/5(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic),(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)CBR(sic)(sic)(sic)(sic)38%(sic)31%. Giroud&Noiray(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)56%(sic)63%,(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)45%(sic)55%. (sic)(sic)(sic)(sic)(sic)(sic)(ANOVA)(sic)(sic),(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic)(sic).

Buried water pipelines, as crucial urban infrastructure, play an essential role. However, the damage to the pipeline structure has emerged as a severe public safety hazard. Monitoring the state of the pipeline structure holds great significance for the normal operation of water pipelines. In this paper, a damage monitoring method for buried pipelines based on distributed acoustic sensing technology is proposed. Through a series of field experiments conducted on a pipeline, the feasibility of utilizing the attached fiber-optic cable to acquire vibration information has been demonstrated. The recorded vibration signals can indicate various damage statuses during the pipeline damage process, including rock/soil fall, pipeline seepage, and pipe wall failure. The results suggest that the fiber-optic cable accompanying the pipelines can be exploited as sensing resources to monitor damage risks to the pipelines, which presents advantages in the damage identification and location of buried pipelines. This research provides a valuable reference for the application of distributed acoustic sensing technology in the damage monitoring of urban buried water pipelines.

Fiber reinforcement has been demonstrated to mitigate soil liquefaction, making it a promising approach for enhancing the seismic resilience of tunnels in liquefiable strata. This study investigates the seismic response of a tunnel embedded in a liquefiable foundation locally improved with carbon fibers (CFs). Consolidated undrained (CU), consolidated drained (CD), and undrained cyclic triaxial (UCT) tests were conducted to determine the optimal CFs parameters, identifying a fiber length of 10 mm and a volume content of 1 % as the most effective. A series of shake table tests were performed to evaluate the effects of CFs reinforcement on excess pore water pressure (EPWP), acceleration, displacement, and deformation characteristics of both the tunnel and surrounding soil. The results indicate that CFs reinforcement significantly alters soil-tunnel interaction dynamics. It effectively mitigates liquefaction by enhancing soil stability and slowing EPWP accumulation. Ground heave is reduced by 10 %, while tunnel uplift deformation decreases by 61 %, demonstrating the stabilizing effect of CFs on soil deformation. The fibers network interconnects soil particles, improving overall structural integrity. However, the increased shear strength and stiffness due to CFs reinforcement amplify acceleration responses and intensify soil-structure interaction, leading to more pronounced tunnel deformation compared to the unimproved case. Nevertheless, the maximum tunnel deformation remains within 3 mm (0.5 % of the tunnel diameter), posing no significant structural risk from the perspective of the experimental model. These findings provide valuable insights into the application of fibers reinforcement for improving tunnel stability in liquefiable foundations.

Alkali-activated concrete (AAC) is a focal point in green building material research due to its low carbon footprint and superior performance. This study seeks to enhance the impact resistance of recycled aggregate concrete (RAC) by elucidating the synergistic mechanisms of alkali activation, nano-modification, and fiber reinforcement. To this end, four mix designs, incorporating NaOH and NaOH-Na2SiO3 systems with 2 % nano-SiO2(NS), were developed and assessed through setting time, compressive strength, drop hammer impact tests, and XRD/ SEM analyses. The NaOH-Na2SiO3 system exhibited a 23.5 % increase in compressive strength over NaOH, achieving 28.41 MPa, while NS refined pore structures, elevating strength to 32.2 MPa; XRD/SEM analyses confirmed mechanisms of pore refinement and interfacial enhancement. In the optimized system, the NT12-C5 formulation, incorporating polypropylene fiber (PPF) and recycled carbon fiber (RCF), exhibited superior impact resistance, with NS enhancing interfacial bonding between carbon fiber and the matrix, resulting in a 47.8 % increase in initial crack impact energy. The Weibull model validated the reliability of impact performance. Furthermore, life cycle assessment revealed that Soil Solidification Rock Recycled aggregate concrete (SSRRAC) substantially reduced carbon emissions compared to ordinary Portland cement (OPC), while maintaining competitive economic costs. This study's innovations include: (1) synergistic optimization of low-carbon AAC performance using NaOH-Na2SiO3 and NS; (2) optimized PPF/RCF formulations promoting the reuse of waste carbon fiber; and (3) application of the Weibull model to overcome conventional statistical constraints. Collectively, these findings establish a theoretical and practical foundation for the global development of sustainable building materials.

In the northwestern saline soils and coastal areas, cement soil (CS) materials are inevitably subjected to various factors including salt erosion, dry-wet cycle (DWC), temperature fluctuations and dynamic loading during its service life, which the coupling effect of these unfavourable factors seriously threatened the durability and engineering reliability of CS materials. Additionally, combined with the substantially extensive application prospects of rubber cementitious material, as a resource-efficient civil engineering material and fibre-reinforced composites, consequently, in order to address aforementioned issues, this investigation proposed to consider the incorporation of rubber particles composite basalt fiber (BF) to CS materials as an innovative engineering solution to effectively enhance the mechanical and durability properties of CS materials for prolonging its service life. In this study, sulphate ions were utilized to simulate external erosive environment and basalt fibre rubber cement soil (BFRCS) specimens were subjected to various DWC numbers (0, 1, 4, 7, 11 and 15) in diverse concentrations (0 g/L, 6 g/L and 18 g/L) of Na2SO4 solution, and specimens that had completed the corresponding DWC number were then conducted both unconfined and dynamic compressive strength tests simultaneously to analyze static and dynamic stress-strain curves, static and dynamic compressive strength, apparent morphological deterioration characteristics and energy absorption properties of BFRCS specimens. Furthermore, further qualitative and quantitative damage assessments of pore distribution and microscopic morphology of BFRCS specimens under various DWC sulphate erosion environments were carried out from the fine and microscopic perspectives through pore structure test and scanning electron microscopy (SEM) test, respectively. The test results indicated that the static, dynamic compressive strength and specific energy absorption (SEA) of BFRCS specimens exhibited a slight increase followed by a progressive decline as DWC number increased. Additionally, compared to 4 mm BFRCS specimens, those with 0.106 mm rubber particle size demonstrated more favorable resistance to DWC sulphate erosion. The air content, bubble spacing coefficient and average bubble chord length of BFRCS specimens all progressively grew as DWC number increased, while the specific surface area of pores gradually decreased. The effective combination of BF with CS matrix significantly diminished pores and weak areas within specimen, and its synergistic interaction with rubber particles efficiently mitigated the stresses associated with expansive, contraction, crystallization and osmosis subjected by specimen. Simultaneously, more ettringite (AFt) had been observed within BFRCS specimens in 18 g/L sulphate erosive environments. These findings will facilitate the design and construction of CS subgrade engineering in northwestern saline soils and coastal regions, promoting sustainable and durable solutions while reducing the detrimental environmental impact of waste rubber.

The stability of soil in high-altitude regions is significantly affected by freeze-thaw cycles, which alter its mechanical and physical properties. This study investigates the impact of 12 consecutive freeze-thaw cycles on poorly graded sandy-silt soil collected from Arunachal Pradesh. To enhance soil resistance, a bio-slurry containing urea (60 g/L) and calcium chloride (111 g/L), along with vetiver and bamboo fibers (by soil weight), was introduced as a stabilizing agent. The durability of the treated soil was evaluated by measuring the weight fluctuations after each cycle and assessing unconfined compressive strength (UCS) after 5, 10, and 12 cycles. The results revealed that untreated soil experienced a 50% reduction in UCS, while bioslurry-treated soil retained 70-80% of its original strength after 12 freeze-thaw cycles. The greatest strength retention was observed in soil treated with bioslurry and bamboo fiber, which retained 80% of its strength, followed by vetiver-treated soil at 75% strength retention. Weight loss measurements indicated that untreated soil samples lost 9.5% of their initial mass, whereas bioslurry-treated samples exhibited only a 3-5% weight loss. The findings of the study highlight the potential of bioslurry and natural fibers in mitigating freeze-thaw-induced soil degradation, making them suitable for applications in geotechnical engineering in cold-climate regions.

Eco-friendly materials have gained significant attention for soil stabilization and reinforcement in road construction and geo-environmental infrastructure, as traditional additives pose notable environmental concerns. In this study, three concentrations of Chitosan Biopolymer (CBP) (1.5 %, 3 %, and 4.5 %) as a bio-stabilizer, three proportions of Rice Husk Biochar (RHB) (0.5 %, 1 %, and 1.5 %) as a waste-derived filler, and three dosages of Hemp Fiber (HF) (0.2 %, 0.4 %, and 0.6 %) as reinforcement were used to treat sand-kaolinite mixtures (SKM). The samples were cured for 1, 7, 14, 21, and 28 days and subjected to varying numbers of freeze-thaw (F-T) cycles. A diverse range macro-scale laboratory tests, encompassing compaction, unconfined compressive strength (UCS), indirect tensile strength (ITS), F-T durability, ultrasonic pulse velocity (UPV), and thermal conductivity (TC), were performed on the treated samples. In addition, microstructural analyses using X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier-transform infrared spectroscopy (FTIR) were conducted to correlate mechanical behavior with micro- scale properties. The optimal dosages of CBP and RHB were first determined through UCS tests, with 3 % CBP and 1 % RHB proving the most effective. These dosages were then used to analyze their impact on other mechanical properties. Results showed that the compressive and tensile strengths of the bio-stabilized soil at the optimum contents of additives increased by 2410.7 kPa and 201.2 %, respectively, compared to the control samples. Incorporating HF into the SKM-CBP-RHB mixtures significantly enhanced their F-T durability after 10 consecutive cycles, reducing strength deterioration and performance degradation compared to the untreated soil. The optimum composition (3 % CBP, 1 % RHB, and 0.4 % HF) led to a 6.1-fold increase in ITS and a minor 2 % reduction in performance after 10 F-T cycles. Moreover, HF incorporation improved the failure strain and reduced the brittleness of the stabilized soil. UPV and TC tests revealed that incorporating HF at levels up to 0.4 %, combined with the optimum CBP-RHB mixture, enhanced soil stiffness by 963.7 MPa and reduced thermal conductivity by 0.76 W & sdot;m-1 & sdot;K-1. The microstructural analysis confirmed these findings, showing enhanced interlocking between SKM and fibers via hydrogel formation. Overall, the study demonstrates that the CBP-RHB-HF composite markedly enhances soil strength and durability, making these additives highly suitable for applications like landfills, embankments, and slopes.

A large diameter triaxial specimen of 61.9 mm was made by mixing coconut shell fibers with red clay soil. The shear strength of coconut shell fiber-reinforced soil was investigated using a dynamic triaxial shear test with confining pressure in a range of 50-250 kPa, a fiber content of 0.1%-0.5%, and a loading frequency of 0.5-2.5 Hz. The Hardin-Drnevich model based on the coconut shell fiber-reinforced soil was developed by analyzing and processing the experimental data using a linear fitting method, determining the model parameters a and b, and combining the influencing factors of the coconut shell fiber-reinforced soil to improve the Hardin-Drnevich model. The results show a clear distinction between the effects of loading frequency and fiber content on the strength of the specimens, which are around 1 Hz and 0.3%, respectively. Hardin-Drnevich model based on coconut shell fiber-reinforced soil can better predict the dynamic stress-strain relationship of coconut shell fiber-reinforced soil and reflect the dynamic stress-strain curve characteristics of the dynamic stress-strain curve coconut shell fiber-reinforced soil.

Soft clay soils inherently exhibit low mechanical strength, imposing significant challenges for various engineering applications. The present research explores various techniques and stabilizers to enhance soft clay's suitability for construction purposes. This study evaluates the mechanism of stabilizing kaolin using recycled macro-synthetic fibers (RMSF) for the first time. Samples were prepared with 5 % LKD, with 25 % replaced by VA, and varying RMSF amounts of 0, 0.5 %, 1 %, and 1.5 % in lengths ranging from 4 to 6 mm. The specimens were cured for 7, 28, and 56 days and exposed to 0, 1, 4, and 10 freeze-thaw (F-T) cycles. Laboratory investigations were conducted through standard compaction, Unconfined Compressive Strength (UCS), Indirect Tensile Strength (ITS), Scanning Electron Microscope (SEM), California Bearing Ratio (CBR), X-ray diffraction (XRD), and Fourier Transform Infrared Spectroscopy (FTIR) tests on the samples at various stages of stabilizer addition, both before and after F-T cycles. The optimal mixture was 5 % LKD, with 25 % VA replacement and 1 % RMSF, which led to a considerable 11-fold enhancement in ITS and a 14-fold improvement in UCS compared to the untreated sample. Additionally, the secant modulus (E50) and energy absorption capacity (Eu) of the sample with the optimal combination content increased in comparison to the stabilized sample without RMSF. The CBR of the optimal sample reached 81 %, allowing for an 87 % reduction in pavement thickness compared to the untreated sample. According to the findings of this research, the combination of LKD, VA, and RMSF increased the compressive and tensile strength properties, bearing capacity, and durability of kaolin, making it an appropriate option for use in various practical civil projects like road construction.

The effective stresses in saturated soils are crucial for geotechnical engineering, particularly in the ocean environment, but no current transducers can directly measure both vertical and lateral effective stresses. Thus, a novel effective stress transducer based on fiber Bragg grating (FBG) technology is developed to directly measure three-dimensional (3D) effective stress in saturated soils. The design of the transducer ensures that pore water pressures inside and outside the transducer are balanced, allowing the strain to solely reflect the effective stress sustained by the soil skeleton. Two FBG sensing elements of the 3D effective stress transducer are designed to measure the vertical and lateral effective stresses by sensing the strain in the thin plate and the sensing cylindrical shell through the porous disk, respectively. Experimental results indicate that the transducer accurately captures the evolution of effective stress under complex static loads and precisely tracks cyclic stress variations under cyclic loadings. Compared to traditional transducers, the lateral earth pressure coefficient derived from the measurement data of the new effective stress transducer shows advanced accuracy and stability. Moreover, the FBG-based transducer effectively monitors effective stress changes during the excavation, capturing soil stress variations and enabling precise excavation stability assessments. The novel 3D FBG-based effective stress transducer offers a vital method for directly measuring the vertical and lateral effective stresses of saturated soils.